034Motorsport Compact Fluid Cooler

Small compact cooler for power steering, transmission, fuel or oil use. Compact 9x3" size fits anywhere and replaces OE unit or supplements cooling.  Uses 5/16" 8mm fittings, includes hose, clamps and mounting tie straps.

Neuspeed Power Pulley Kit for B7 A4 2.0T

Your car's power steering pump, alternator and A/C are powered by a belt connected back to the crankshaft pulley. Spinning these pulleys draws precious horsepower from your engine. NEUSPEED's powertrain engineer, using sophisticated CAD software,...

Neuspeed Engine Torque Damper Bushing for B6 1.8T & B7 2.0T

Launching your car at full throttle from a standing start will usually result in an annoying "clunk" followed by a slight vibration. This is caused by excessive engine and drivetrain movement. NEUSPEED's engine torque damper is a urethane bushing that...

CJM Industries AEM Sensor Mounting Bracket

A simple solution to mount AEM sensors under the hood or in your car. Made of ABS composite. 3D printed part, layer lines are visible. No sensor included, mounting bracket only. Each order will be 1 bracket, 2 zip ties, and VHB tape to adhere to your car...

034Motorsport Billet Aluminum Rear Main Seal for Early 1.8T & 2.0T

*Fitment Notes: Will NOT fit 2.0 TSI engines in later model MK5, B6, etc. B5 Passat & Audi A4 1.8T Owners - This will only fit engine codes AUG or AWM* 034Motorsport’s Billet Aluminum Rear Main Seal is designed to replace the failure-prone...

Fluidampr Crank Pulley for 2.0T FSI

Fluidampr Engine Dampers are designed to control destructive vibrations which are transfered thru the crankshaft. Each time the air/fuel mixture inside a cylinder is ignited, the combustion that occurs creates a torque spike that is applied to the...

034Motorsport Motor Mount Pair - Motorsport for Audi B5, B6, B7 & C5

We're proud to announce the availability of the Motorsport Engine Mount Pair for B5, B6, B7, and C5 Chassis Audi and B5 Chassis Volkswagen models! 034Motorsport's Motorsport Engine Mounts are the new standard in track performance. Our mounts are...

034Motorsport Silicone High Flow Turbo Inlet Hose for B7 2.0T

OEM rubber turbo inlet boots do the job OK on a stock application, but are prone to problems once boost is turned up and performance increased.  Due to the lack of reinforcement, it's common to see the stock hose collapse under vacuum created by the...

034Motorsport Density Line Motor Mount for Audi B5, B6, B7 & C5

*Sold individually. One vehicle will require 2 mounts!* We're proud to announce the availability of the Density Line Engine Mounts for B5, B6, B7, and C5 Chassis Audi and B5 Chassis Volkswagen models! 034Motorsport's Density Line Mounts are the new...

034Motorsport Billet Oil Catch Can Kit for B7 A4 2.0T

The 034Motorsport B7 Audi A4 2.0T FSI Catch Can Kit is here! We've put months of engineering and testing to create the most complete and effective catch can kit on the market. The 034Motorsport B7 Audi A4 2.0T FSI Catch Can Kit features a completely new...

034Motorsport Oil Catch Can Kit for B7 A4 2.0T

We've been hard at work on our new 034Motorsport B7 Audi A4 2.0T FSI Catch Can Kit! This kit was designed to offer bolt-on installation and hassle-free use, with a fully-recirculating design and oil drain system to ensure that the can never has to be...

034Motorsport Street Polyurethane Snub Mount with Bracket for B6 1.8T & B7 2.0T

This snub bracket is designed for the included Polyurethane Snub Mount, and unlike other snub mount kits on the market that allow an "air gap" around the mount, our mount fits tightly inside the bracket for a tight precision fit. Greatly reduces...

034Motorsport Polyurethane Snub Mount for Audi B6, B7, C5 3.0 & C5 4.2

This 70 durometer performance polyurethane snub mount fits most late-model Audi vehicles manufactured after 2002, and is designed to increase stabilization of the motor under acceleration. 1mm undersized for vibration free performance when no load is on...

034Motorsport Valve Cover Breather Adapter with Nipple Fittings for 2.0T FSI

DIY breather port adapter to allow a provision for custom catch can setups on the Audi/VW 2.0T FSI. Features: CNC Machined from solid 6061 aluminum Allows stock breather port to clip right on 21mm OD (11mm ID) inlet and outlet male bungs Allows oil...

034Motorsport Valve Cover Breather Adapter with -10AN Fittings for 2.0T FSI

DIY breather port adapter to allow a provision for custom catch can setups on the Audi/VW 2.0T FSI. Features: CNC Machined from solid 6061 aluminum Allows stock breather port to clip right on -10 AN inlet and outlet male bungs Allows oil fumes from...